On this page down the page you will find additional good insight involving How to Install a Bathtub Yourself.
Mounting a tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult project. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open up a wall surface to get rid of the old tub as well as place the brand-new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will require a helper to vacate the old bathtub and set in the brand-new one. Make sure you have actually qualified yourself for the work and also fit trying it. Instead of employing a service provider to take control of a halfway-completed project, it is much better to consider employing one before you begin. Opportunities are you might require an expert plumber to make tube links.
This post will assist you install a new bathtub in your bathroom if you have actually currently gotten a new tub and also do not need to change the arrangement of your previous water supply pipelines.
Your devices as well as material checklist need to consist of the following:
Getting ready for the Installation
To start with, the sustaining frame provided with the bath should be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps device to prevent strain on the bath tub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be suited its final position.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you should do is disconnect the water system. After doing so, activate the faucets to drain any kind of water remaining in the system. The process of eliminating the existing taps can be rather bothersome as a result of the limited gain access to that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the staying water that will certainly originate from the pipes. Once the supply pipes have been gotten rid of, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Before moving on to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, place the bathtub in the called for position. The wood boards are helpful in evenly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The following goal is to ensure that the bathtub is leveled all round. This can be attained by checking the level as well as readjusting the feet on the bath tub until the spirit level reads level.
To install faucets, fit the bottom of the outermost versatile faucet adapter to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Switch on the water as well as check all joints and also brand-new pipework for leaks and tighten them if essential. Load the tub as well as also examine the overflow outlet as well as the typical outlet for leaks.
Finally, fix the bath paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bathtub ought to wait up until the bath tub has actually been utilized a minimum of once as this will certainly settle it right into its last position.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in location in between the faucet as well as the sink. Safeguard the tap in place with the maker given backnut. When the tap is firmly in place, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type should be linked to the faucet ends initially, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to break a rigid seal, causing the water to pass through the wall surface in between the bathroom as well as the tiling, causing issues with moisture and feasible leakages to the ceiling below.
You can select from a variety of coloured sealers to assimilate your components and also fittings. They are sold in tubes as well as cartridges, and can securing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill up the tub with water prior to sealing, to enable the movement experienced when the bathtub remains in usage. The sealer can split rather very early if you do not take into consideration this movement before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is advisable to fit the tiles making use of waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been shown that write-up about Installing A Bathtub through a good friend on our other domain. If you please take a moment to share this blog posting if you liked it. Thanks so much for going through it.
Clog issue? Reach out!